Become a TherMark Distributor

 

TherMark GlobeTherMark is expanding its distribution network. Click Here for more details.

LMM14 Black for Metal (General Purpose)

Recommended use
LMM14 is one of TherMark’s two general purpose laser marking inks and is recommended for creating a black mark on most metals. The combination of its flexible process window and wide range of applicable substrates makes LMM14 an extremely easy product to use. In general, if you are looking for one laser marking product to keep on your shelf, we recommend LMM14.


LMM14 dries quickly as a light-gray powder coat and is extremely easy to wash after laser marking. This coat should not be extensively handled prior to laser marking, however, so LMM14 should be marked shortly after application.

If you are interested in a general marking product which dries in a more durable hard coat, please check out our LMM6000.

 

Recommended substrates:
LMM14 is an extremely flexible product which is recommended for almost any metal. The following list is made up of substrates on which LMM14 works well. This list is not exhaustive, however, so if your substrate does not appear on the list, this does not mean LMM14 will not mark it.


Stainless Steel Chrome Plating
Stainless Steel - Bright Annealed Nickel Plating
Galvanized Steel Gold Plating
Brass Silver Plating
Aluminum Titanium
Copper Pewter


Lasers that work:
LMM14 works equally well with CO2 and solid state lasers.

Dilution:
LMM14 will need to be diluted differently depending on how you plan to apply it.

  • Air brush application: Ratio of 1:1 (1 part in volume of LMM14, 1 part in volume of denatured alcohol) is recommended. Please refer to your air brush manual for information about material thickness for your model type.

  • Foam brush (hand) application: Ratio of 2:1 (2 parts in volume of LMM14, 1 part in volume of denatured alcohol) is recommended.

For more information on dilution, click here.

Application methods:
Please make sure that the surface to be marked is free and clear of oils, cleaning agent films, dust, and lacquer coating.

  • Aerosol application: Shake the aerosol can thoroughly before use to achieve a homogenous suspension of marking material inside the can. When applying LMM14 from an aerosol can, the resulting coating of LMM14 should be about 1 mil thick (~25 μm). Spray uniformly at a 10” distance from the surface and move the nozzle from one side to the other covering the whole substrate area. Start spraying away from the area to be marked and move towards the opposite side and past the target area. Over-spraying before and after the target area allows constant velocity of movement and will help provide an even coating on the substrate. Make sure the bare metal is not visible underneath. If necessary spray one or two more times. In general 2-3 strokes are enough to generate the desired coating.
     
  • Air brush application: When airbrushing use the above mentioned procedure for aerosol application.

  • Foam brush (hand) application: When hand applying LMM14 the resulting coating of LMM14 should be 1-2 mils thick (~25-50 μm). Use about a 1” wide foam brush and soak less than ¼” of the brush with LMM14. There is no need to soak more than that, otherwise the ink may splash and result in an uneven coat thickness. Apply with smooth, even strokes.

    Note: Aerosol and air brush application are both preferred over foam brush application. It can be challenging to achieve the smooth, even coating of laser marking material necessary for optimal marks when using a foam brush. We only recommend foam brush application if you do not have an air brush or are coating a small surface area.


For more information on application,
click here.

Drying time & methods:
If left to air dry, LMM14 is normally fully dry within about two and a half minutes. If air drying takes too long, however, a hair drier or forced air heater may be used to speed up the process. LMM14 can be fully dried with an average household hair dryer in 5-7 seconds.

Laser settings:
Power and speed are the two most important variables to control when using TherMark laser marking materials with any laser, but there are other relevant variables depending on which laser you are using, such as length of lens, PPI, DPI, frequency, or hatch spacing. To read more detailed information on laser settings please click here, or follow the link below to download a recommended settings chart of LMM14 on various substrates.


LMM14 Laser Settings Chart


Product Appearance:

LMM14 liquid will often separate and needs to be well-stirred prior to use. The dense, heavy part of the marking material containing frit and pigment is silver/gray in color, while the thin, light part of the marking material containing mainly thinning agent may be yellowish green or greenish blue.

Once applied to the substrate and dry, LMM14 will be a light-gray powder coating.

Shipping options:

  • LMM14 aerosol is considered by the US Department of Transportation (DOT) to be “ORM-D” or “Consumer Commodity”. This product is generally shipped via ground in the contiguous United States. Products shipped via air to Hawaii or to international destinations will be subject to additional hazardous materials charges. This is due to regulations around the shipping of pressurized cans on airplanes. Please contact customer service for further details.

  • LMM14 liquid is a non-hazardous, water-based product and can be shipped via ground or air with no additional charges.

Product storage:
All LMM14 products should be stored between 40ºF (5ºC) and 95ºF (35ºC) in a dark, dry place. Aerosol cans should be stored on their side rather than their bottom, as the LMM14 material can settle and clump together inside the can. Side storage makes it easier to achieve even dispersion when the cans are shaken.

Disposal:

LMM14 is a water-based material and is environmentally safe and non-hazardous. After laser bonding, any excess, un-bonded material can be washed off the substrate and down the drain into your normal water/sewer waste area.

Unused aerosol cans that are still pressurized should be de-pressurized in a well-ventilated area (the propellants should be completely expelled from the can) and then can be disposed of in your regular trash and solid waste area.

Unused containers of liquid ink/paste can be safely disposed of in your regular trash and solid waste area.

Buy Now:
LMM14 comes in 5 sizes:

LMM14.TM.A6 6oz aerosol
up to 900 sq/in
~$.065 per sq/in $62.65
LMM14.TM.50 50 gm liquid ink
up to 1,200 sq/in
~$.049 per sq/in $62.65
LMM14.TM.250 250 gm liquid ink
up to 6,000 sq/in
~$.025 per sq/in $164.65
LMM14.TM.500 500 gm liquid ink
up to 12,000 sq/in
~$.022 per sq/in $277.95
LMM14.TM.1000 1,000 gm liquid ink
up to 24,000 sq/in
~$.019 per sq/in $499.95

 

* Product coverage in above table assumes proper application (dilution/coating thickness).

Downloads:
LMM14 aerosol MSDS
LMM14 liquid MSDS

LMM14 Data Sheet
LMM14 Laser Settings Chart